保压压力,packing pressure
1)packing pressure保压压力
1.The effect ofpacking pressure and packing time on thickness distribute of injection molding parts;保压时间和保压压力对注塑制品厚度分布的影响
2.Optimization of injection moldingpacking pressure curve based on ActiveX and MPI基于ActiveX和MPI优化注射成型保压压力
3.Thepacking pressure,melted mass temperature,mold temperature and cooling time were also analyzed by using orthogonal experiment method.利用Moldflow软件对注射器塑料件的翘曲原因进行分析,并采用正交试验设计方法(单参数变动实验)对保压压力、熔体温度、模具温度、冷却时间等进行分析。
英文短句/例句
1.Optimization of injection molding packing pressure curve based on ActiveX and MPI基于ActiveX和MPI优化注射成型保压压力
2.Response of Cavity Pressure During Pulsatile Pressure Induced Packing脉动压力诱导保压过程中的模腔压力响应
3.maintained at a certain atmospheric pressure.保持特定的空气压力。
4.protective pressure signaling unit保护性压力信号装置
5.Lower to note the pressure of mold, reduce to model and protect to press time.降低注塑压力,减少成型和保压时间。
6.Design of Oil Pressure Supervisory and Protection System for Power Transformer电力变压器油压监测与保护系统设计
7.Pressure Setting of Press-keeping Clamping Circuit Based on Accumulator基于蓄能器保压夹紧回路的压力设定
8.osmotic pressure渗透压(力), 浓差压
9.To crush or press down on with physical force.压倒用体力压倒或压迫
10.The hot water is brought to a container where the pressure is kept below 0. 5 atmosphere.热水引到压力保持在0.5大气压以下的扩容器中。
11.The Principle of the Overload-Protective System Applied in Series JZ21 Barometric Press;JZ21系列压力机专用气压式过载保护系统原理
12.hydrostatic extrusio静水压挤压;静水压挤压;静液力挤压;静液力挤压;液力静挤压
13.isostatic presses (cold and hot)等静压压力机(冷压和热压)
14.To exert force or pressure.挤,压运用力量或压力
15.pressure converter压力变换器压力转换器
16.a manometer for measuring vapor pressure.测量气体压力的压力计。
17.pressure controlled valve压力调节阀压力控制阀
18.overvoltage protection varistor过电压保护压敏电阻器
相关短句/例句
pressure maintenance压力保持
3)pressure upkeep保持压力
4)protection pressure保护压力
5)ensure the strength of clamping保证扣压力
6)pressure-support well压力保持井
延伸阅读
注塑成型之保压压力保持压力的设定是为使树脂在冷却的过程中不致产生回流,且能继续补充因树脂冷却收缩而不足的空间,而得到最佳的模具复制效果。 保持压力设定过高,易造成毛边、过度充填浇口附近的应力集中等不良现象,保持压力设定过低,又易造成收缩太大、尺寸不安定等现象。 保持压力必须伴随保压切换点及保压时间设定方为有效。 保压不足时会导致:1.凹陷;2.气泡;3.收缩率增加;4.成形品尺寸变小;5.尺寸的波动性变大;6.由于熔胶回流导致内层配向。 过大的保压则会造成: 1.注道(Sprue)区域的应力; 2.脱模困难; 3.外皮层的拉伸应力。 保压时间阶段逐次降低保压可(多段保压): 1.减少翘曲、降低从 浇口到末端的成形品区域之收缩变异; 2.减少内应力; 3. 减少能源损耗。